}
}
}Graphtec CE6000-40 Teflon Cutting Strip 2-Pack CE6-CM40-2
Brand: GRAPHTEC
Tax excluded. Shipping calculated at checkout
Availability: In stock
%20is%20the%20genuine%20original%20Graphtec%20replacement%20cutting%20mat%20strip%20for%20the%20CE6000-40%20and%20CE6000-40%20Plus%20cutting%20plotters%20%E2%80%94%20t...
){kind=link}
The Graphtec CE6000-40 Teflon Cutting Strip 2-Pack (part number CE6-CM40-2) is the genuine original Graphtec replacement cutting mat strip for the CE6000-40 and CE6000-40 Plus cutting plotters — the 15" model of the CE6000 series. This 2-pack consumable protects the platen gutter rail from blade contact and shields the blade from premature dulling during through-cut work. Each pack contains 2 strips, 10mm wide and pre-cut to the CE6000-40's gutter rail length, with an aggressive adhesive backing and a rigid Teflon (PTFE) base on the blade-facing side. Every CE6-CM40-2 we stock at Digiprint USA is 100% genuine original Graphtec — not aftermarket, not generic..
Product Details
| Specification | Detail |
|---|---|
| Graphtec Part Number | CE6-CM40-2 |
| Compatible models | Graphtec CE6000-40, CE6000-40 Plus (15" cutting width) |
| Quantity per pack | 2 strips |
| Strip width | 10mm |
| Length | Pre-cut to CE6000-40 gutter rail length (15") |
| Material | Teflon (PTFE) — rigid non-stick base |
| Adhesive | Single-sided aggressive adhesive backing |
| Cutting face | Rigid Teflon base (non-stick, blade-facing side) |
| Recommended replacement interval | Every 6 months in regular production use; inspect monthly |
| Condition | 100% genuine original Graphtec, brand new |
CE6000 Cutting Strip Part Numbers by Model Size
Order the correct part number for your specific CE6000 model:
| CE6000 Model | Cutting Width | Part Number | Pack |
|---|---|---|---|
| CE6000-40 / CE6000-40 Plus (this listing) | 15" | CE6-CM40-2 | 2-pack |
| CE6000-60 / CE6000-60 Plus | 24" | CE6-CM60-2 | 2-pack |
| CE6000-120 / CE6000-120 Plus | 48" | CE6-CM120-2 | 2-pack |
Graphtec Cutting Strip Platform Comparison
Different Graphtec cutter series use different cutting strip formats. None are interchangeable:
| Cutter Series | Part Number Format | Strip Width | Pack |
|---|---|---|---|
| CE6000 (this listing) | CE6-CMxx-2 | 10mm | 2-pack |
| CE7000 | PM-CR-009 | 10mm | 2-pack |
| FC9000 | PM-CR-005 to PM-CR-008 | 10mm | 2-pack |
| FC7000 / FC8000 / FC8600 | 51407-141 to 51407-145 | 5mm | Single strip |
What Does a Cutting Strip Do?
The cutting strip — the black strip running the length of the cutter under the blade — sits in the gutter rail of the CE6000 platen. It provides a safe, controlled surface for the blade tip to fully penetrate during through-cut work without contacting the bare metal rail beneath, cushioning blade contact to prevent premature dulling and tip chipping. A worn or deeply grooved strip causes inconsistent blade penetration depth, producing unclean cuts, media lifting on contour paths, and accelerated blade wear. Keeping a 2-pack in stock means one strip installed and one ready — no production delay when the strip needs changing.
When to Replace Your CE6000-40 Cutting Strip
As a general guideline, replace every 6 months in regular production use — and inspect monthly. Replace immediately when you notice:
• Deep grooves worn into the strip surface along the primary cutting path
• Incomplete cuts despite correct blade force and depth settings
• Media lifting or pulling during cutting
• Blade tips dulling faster than normal
• Visible crumbling, discolouration, or loss of the non-stick surface
Installation Notes
Clean the gutter rail thoroughly with isopropyl alcohol to remove residue from the old strip. Allow to dry completely. Peel the adhesive liner, align one end with the gutter rail, and press firmly along the full length. Allow 15–30 minutes before running a cutting job. After installation, verify blade force and depth settings — the fresh strip surface may require minor adjustment.
Why Buy from Digiprint USA
• 100% genuine original Graphtec CE6-CM40-2 — not aftermarket, not generic
• 2-pack — one to install, one in reserve
• In stock in Doral, Miami FL — same day shipping before 2PM EST
• All three CE6000 sizes stocked (CE6-CM40-2, CE6-CM60-2, CE6-CM120-2)
• Ideal for Latin American sign shops and vinyl cutting operations using Miami freight forwarders
View our full range of genuine Graphtec spare parts and accessories stocked by Digiprint USA.
Frequently Asked Questions
Is CE6-CM40-2 compatible with the CE6000 Plus?
Yes. The CE6000-40 Plus uses the same gutter rail and cutting strip specification as the standard CE6000-40. CE6-CM40-2 is the correct replacement for both variants.
Can I use the CE6000 cutting strip in a CE7000 or FC9000?
No. While the CE7000 (PM-CR-009), FC9000 (PM-CR series), and CE6000 (CE6-CM series) all use 10mm wide strips, they are cut to different lengths specific to each machine's gutter rail. Using the wrong length strip leaves sections of the gutter rail unprotected. Always order the strip corresponding to your exact cutter model.
How often should I replace the cutting strip?
Every 6 months in regular production use is the recommended interval. For lighter hobby or occasional use, inspect the strip every few months and replace when visible grooving appears along the cutting path. The 2-pack means you always have a replacement on hand — no waiting for restock when the strip finally wears out.
Do you stock CE6000-60 and CE6000-120 cutting strips?
Yes — CE6-CM60-2 (24" / CE6000-60) and CE6-CM120-2 (48" / CE6000-120) are both stocked. Search by part number or contact us to order.
